Pressure sensor PT2 - DIN 43650A

Product information "Pressure sensor PT2 - DIN 43650A"

This sensor was developed for economical pressure measurements. Beside the usual sensor applications, for example feedback for control systems or continuous surveilance, this sensor can also replace pressure switches due to the low costs. The sensor can be used to surveil a multitude of mediums due to the high quality of materials that have been used. Up to 80°C the sensor is temperature compensated to increase the quality of the results.

Other options are available as special orders, different output signals with lower voltages for single board computers and different pressures. You can find this sensor with other electrical connectors under the tab similar products.
This pressure sensor is by default equipped with a DIN 43650 A connection. Another designation for the connection is DIN EN 175301-803.
Included: Sensor, connector with gasket

Electrical connection:	DIN 43650A

Accesories

Sensor LED Display with switch functionalities NOM13

This display is intended to add a direct read-out as well as pressure switch functionality to sensors.The display is simply plugged into the sensor, please note that the 43650A connection on the output side has a different layout to accomodate the two switches.As an LED display, it can be easily read in dark conditions.Configuration is done with the two buttons at the front, which can easily be done, even in the field.The two npn exits have a maximal output of 100 mA. These can be freely configured as NO, NC, set point and hysteresis.Due to the low voltage loss, the normal power supply of the sensor can simply be used. An additional power supply is therefore not necessary.Again please note that the DIN43650A output layout is different from the usual layout, check the data sheet for details.The display has to be configured by the customer.

From €44.91*

Details

Display NOM11 DIN 43650A connection to the control unit

Sensor LCD Display NOM11

This plug-In display is intended for integration into existing sensor connections.This display is compatible, depending on the variant, with all sensors, which have a 0 - 10 V or a 4 - 20 mA signal.Connecting the display is very simple as the original signal is passed through. Simply open the existing DIN 43650A connection, insert the display and close the connection again with the included longer screw.If the display has not already been configured, you can configure it now.Because the display causes a voltage drop of less than 3.5V, in most cases the supply voltage of the sensor does not need to be raised. An additional power source is not needed.Once the display is configured, it can be used as a quick monitoring tool in case of problems. Within a minute the display is installed, the measured value of the sensor is displayed and the source of the problem can be narrowed down.This way you can save valuable time solving the problem.Due to the low cost of the display it is economical to outfit an existing sensor with it than to have a manometer at a different connection.The display is equipped with background lighting, offering tireless readThe illumination of the display enables fatigue-free reading even in dark surroundings. Included: Display, with DIN 43650A connection: long screw as well as gasket as seen on the picturesConnection layout: DIN 43650A: 4 - 20 mA: 1: + 2: - 3: empty; 0 - 10 V: 1: + 2: - 3: signalThe display has to be configured by the customer.

From €30.38*

Details

Sensor LED Display with switch functionalities NOM13

€79.00*

Details

Reduction G 1/2 to G 1/4 with aluminium washer

Reducing nipple with aluminium seal outer thread 1/2 inner thread 1/4 for pressure sensors PT2

This reducer can be used if the PT2 sensors are to be fitted to a G 1/2" connection instead of a G 1/4" connection.Materials: Brass (reducer), aluminium (sealing washer)Temperature range: -40 ~ 150 °CPermissible pressure: 60 bar (reducer), 18 bar (sealing disc)

€12.70*

Details

Sensor LCD display with control functions NOM12

From €101.97*

Details